XBOX 360 Water Cooling system !
Specially design for XBOX 360 systems
Ask any Xbox 360 owner what their greatest fear concerning their $300-$400 piece of machinery is, and you might receive a variety of answers. For some, the words “Halo 3” and “cancelled” being in the same sentence might bring nightmares to their otherwise soothing dreams. For others, terror might set in at the mere idea of trying to afford a new HD television to take advantage of all the bells and whistles associated with their beefy console. However, one concept that is sure to make the blood run cold in any Xbox 360 owner’s veins is the sight of the dreaded “red ring of death”.
The dreaded flashing red lights of death!
Syscooling has just announced a liquid-cooling system that totally replaces the original air-forced cooling of the Xbox 360.
Black & White color available!
Included all necessary mounting hardware and fittings! (except the cooling coolant,we could not ship the coolant due to carrier do not ships liquid,you can use common water instead of it)
XBOX360 Water Cooling System Instruction For Installation
You are going to need a few tools to get your Xbox 360 apart for this project: A set of Torx screwdrivers(T10 & T8)/wrenches; a small, flathead screwdriver(Φ2 ); a pair of needle nose pliers; and a long, thin pick or flat metal rod(XBOX360 Unlock Kit);electric drill with drills(Φ3 & Φ10)
Configuration
|
Name |
Quantity |
|
Xbox360 Block |
2 |
|
12V Pump |
1 |
|
|
1 |
|
Reservoir(integrate) |
1 |
|
AC Adapter |
1 |
*included all necessary fittings and mounting hardware as below.
While it may seem a bit daunting at first because the Xbox 360 has no outside screws, cracking the console open is relatively easy. Even if you have a limited amount of patience you can get the case apart in about 30 – 45 minutes. First of all, you will want to remove the faceplate from your system. This is a simply a matter of squeezing the sides of the faceplate while pulling outward until it pops off. You can also use the USB door hole or get your fingernails into the seam at the base of the faceplate and pull. I don't explain disassembling Xbox 360 part in detail now,please search in google.
On the back side of the motherboard you will see two large “X” shaped heat sink retention mechanisms. The “X” design uses tension to hold the heat sink in place; you must use the flathead screwdriver(Φ2 ) to gently pry the clip mechanism up and over the heat sink retention studs. I recommend doing one side at a time (versus a cross pattern) to make removal easier. With the retention clip removed, the heat sink can now be removed.
You have now completed the disassembly portion of this mod. Let’s take a look at what you are going to need for the water cooling portion.
There is a perfect space, right above the video header/port.
To drill two holes(radius
After dug the hole, through the screw, as below:
After that's easy
Cut 
Be careful not to screwed it too tightly, or your work will lose mainboard’s shape.
put the silicone grease thermal compound cover on the core of CPU and GPU.
Be careful,twisting bolts well-distributed
As far as I could see, it only needed a minor adjustment,the nut not over the thread,it will be in the right place,just like below picture is enough.
If you screw the nut too tightly, red lights of death will appear.
Connect all silicon tube
Replace all parts
Turn out 4 screws and open the Water Cooling System case , twisted off the water pump cap,use the injector fill water into pump.
During the fill in,for get rid of the air from heat exchanger,you need close the dump with your hand, turn over the Water Cooling System case slowly,till to water full.
Power on the Water Cooling System,you can see water flowing.
After all finished , you must running leak test over 4 hours .
| Total Rate： | Review Summary: 0 reviews | Write a review |
